Did you know?

If litter robot is flashing blue, yellow and red then this means it cannot find the dump position. What the video for the fix!Jun 29, 2017 · To troubleshoot the blue blinking, let’s start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait 10 seconds then plug the unit back in 3.) Allow the unit to complete a startup cycle. If the light is solid blue, the code has been successfully cleared. Litter-Robot Customer SupportPhone: 1-877-250-7729 | Hours: 9am – 7pm ETEmail: [email protected]. We have had our Bisque-colored (we just got a Grey LR III) Litter-Robot Open Air for 3 years. Here’s the email that LR sent me that I reference in our “repair” video: If the Litter-Robot 3 cannot find the Dump and/or Home position ...Slow blue light --> fast yellow flashing light. I have a pretty old LR 3 (non-Connect, serial # 028957). I replaced the DFI and pinch detect terminals about 1.5-2 years ago and it's been working pretty well since then. A few days ago, the unit stopped cycling entirely. The blue DFI light started blinking even when the tray was empty, and after ... 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait 10 seconds then plug the unit back in 3.) Allow the unit to complete a start‐up cycle. If the light is solid blue, the code has been successfully cleared. If the light is still blinking, let’s proceed with troubleshooting.Jul 23, 2016 · 1.) Press/Hold ‘Cycle’ button for 5 seconds. Both blue AND yellow lights are now on. 2.) Press/Hold ‘Cycle’ button for 5 seconds. Yellow light turns off, blue light remains lit. 3.) Activate the cat sensor by pressing on the globe just above the entrance in a forward and down motion. The red light should come on now. If the blinking blue light is caused by a firmware update, wait for the firmware update to complete and then unplug the unit for 10 seconds before plugging it back in. Firmware updates are done to improve the performance and security of the Litter Robot.The globe stayed up, the light changed from flashing rapid yellow, to flashing blue. More happened in between me fiddling around with it but I took off the base, cleaned it out, cleaned the sensors, the pinch detector, the bin. Messed the app up so now it says it's off (the cloud?), the app still turns the power and light.To troubleshoot the blue blinking, let’s start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait 10 seconds then plug the unit back in 3.) Allow the unit to complete a start‐up cycle. If the light is solid blue, the code has been successfully ...Inspect the Position Sensor. If you've just installed and/or replaced the Connect Upgrade Kit, the Drawer Full Indicator, Motor, Control Panel, or any other components within the motor cavity in your unit, and now you're getting three flashing lights, it is most likely due to the Position Sensor being out of place. Power off and unplug the unit. The order number is 1176529. Thank you for your reply. According to your order number, the robot is no longer under warranty. If the cleaning of the DFI sensor didn’t fix the issue, we recommend replacing it so you can order a new one from this link: We also recommend replacing the 3 sets of pins so you can order new ones from these links:If both the blue and yellow lights are illuminated on your Litter-Robot 3, it means that the unit is in 8-hour sleep mode. (The unit will not cycle automatically during those 8 hours.) If you’d like to deactivate sleep mode, press and hold the Cycle button for 5 seconds.When I press the rest button, the blue light goes out and the yellow light flashes quickly. I have checked and cleaned the pinch sensor, no change. If I press reset repeatedly the blue and yellow lights will alternate: blue flashing RESET yellow flashing RESET blue flashing, etc. I can't get the unit to cycle at all, it won't empy, it is ...During each Clean cycle, the DFI Sensor will measure the level of waste within the Waste Drawer as the Waste Port passes over the Waste Drawer. Once a full Waste Drawer is detected, the unit will indicate it is full with a blue light bar flashing. You will also receive a notification on your phone if you use the Whisker App. Ever since I changed the last bag, my litter robot 3 has had its blue light blinking after every use. I can hit reset and it stops, until the next time it is used. Will deep cleaning help? I open the drawer every morning to rearrange things as it tends to pile up in the back of the tray. The bag is not higher than the drawer. This is happening ...Jan 13, 2023 · The Litter Robot is a self-cleaning litter box that makes life easier for cat owners. It has a built-in sensor that detects when your cat has used the litter box, and then automatically rotates and separates the clumps into a waste drawer. The blue light on the Litter Robot indicates that it is in standby mode or working properly. Brand new Litter Robot flashing Blue - Red Sequentially. Hey everyone - we got a Litter Robot and it started flashing Blue then Red immediately after running a cycle. Chatted with customer service and they said it was an over-torque issue. They sent a new base yet I'm getting the same flashing Blue - Red lights.Inspect the Position Sensor. If you've just installed and/or replaced the Connect Upgrade Kit, the Drawer Full Indicator, Motor, Control Panel, or any other components within the motor cavity in your unit, and now you're getting three flashing lights, it is most likely due to the Position Sensor being out of place. Power off and unplug the unit.Dec 10, 2021 · 1. Empty the Drawer. On the Litter-Robot, you have a drawer that collects the cat litter. If it becomes full, the blue light will blink rapidly. But if you throw out the mess, the lights should go off. Before returning the drawer to its compartment, remember to place a new liner into the container. Now, the “ready” light flashes blue and when I press the reset button, the “cycling” light flashes yellow/amber rapidly. I Googled this and seems to be an indicator that the weight or anti-pinch sensors are being tripped (based on the flashing yellow/amber “cycling” light). I unplugged the robot and disassembled and used a q-tip to ...Now, the “ready” light flashes blue and when I press the reset button, the “cycling” light flashes yellow/amber rapidly. I Googled this and seems to be an indicator that the weight or anti-pinch sensors are being tripped (based on the flashing yellow/amber “cycling” light). I unplugged the robot and disassembled and used a q-tip to ... 5. Blue Light Blinking. Regarding issues with your Litter-RobTo troubleshoot the blue blinking, let’s start by power cycling Hi, I need help with my litter robot 3 please. The blue light is blinking although the waste drawer is empty. The other buttons do not react to pushing except the on/of one. ... Blue light blinking - Litter robot 3. Help & Support. Domestic Robots. Mariagav July 1, 2023, 10:15pm 1. Hi, I need help with my litter robot 3 please.The unit is pushed into a corner, against a wall, or furniture. The red blinking light indicates CATS (the cat sensor) is detecting excess weight for more than 2 minutes. To test your changes, power the unit off and then on. Allow the unit to complete the start‐up cycle and return Home with a solid blue light. at home position while Blue LED is illumiated ( My Litter Robot won’t reset. The blue light is constantly flashing. When reset is pressed the yellow light then flashes. It pinch sensor has been cleaned and they are touching. ... Litter-Robot III Open Air - Yellow Blinking Light. igor_X July 21, 2020, 5:30pm 3. Hi @Hemingway1! Thank you for contacting us. It seems that DFI sensor should be ...Select your Litter-Robot 4. Select the Settings gear in the top right corner. Select Update Network. Follow the steps listed within the App. Once the update is complete, your Litter-Robot should be ready for use. If your unit displays a solid blue light bar, you've been successful. If your unit is not displaying a solid blue light bar, your ... To confirm the DFI has failed when there is

If your unit has a red flashing light bar or the unit will not cycle, this indicates that the cat sensor has been triggered for more than 30 minutes. You will also receive a notification on your phone if you use the Whisker App. Successful: If your unit returned home and displays a blue light bar, you've been successful.Now, the “ready” light flashes blue and when I press the reset button, the “cycling” light flashes yellow/amber rapidly. I Googled this and seems to be an indicator that the weight or anti-pinch sensors are being tripped (based on the flashing yellow/amber “cycling” light). I unplugged the robot and disassembled and used a q-tip to ...If your robot has problems with the yellow blinking light, please follow the troubleshooting below to determine whether the issue is due to excess weight, the bonnet connection, or the Anti-Pinch safety feature: *The blinking yellow light will switch to blinking red after 2 minutes if the cat sensor (CATS) has been continuously activated by …In this video we'll be taking a look at 5 different errors the Litter-Robot 4 may run into and how to fix them. This include LED status identification of the...

Now, the “ready” light flashes blue and when I press the reset button, the “cycling” light flashes yellow/amber rapidly. I Googled this and seems to be an indicator that the weight or anti-pinch sensors are being tripped (based on the flashing yellow/amber “cycling” light). I unplugged the robot and disassembled and used a q-tip to ...Jul 23, 2016 · 1.) Press/Hold ‘Cycle’ button for 5 seconds. Both blue AND yellow lights are now on. 2.) Press/Hold ‘Cycle’ button for 5 seconds. Yellow light turns off, blue light remains lit. 3.) Activate the cat sensor by pressing on the globe just above the entrance in a forward and down motion. The red light should come on now. To troubleshoot the blue blinking, let’s start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait 10 seconds then plug the unit back in 3.) Allow the unit to complete a start‐up cycle. If the light is solid blue, the code has been successfully ...…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. If you’re anything like us, you’re probably . Possible cause: Ever since I changed the last bag, my litter robot 3 has had its blue light blinking afte.