Did you know?

Litter-Robot 3: All three lights flashing (Position Sensors) Litter-Robot 3: Blue Light Flashing (Drawer Full) Litter-Robot 3: Buttons and Lights Litter-Robot 3: Cat not detected ; Litter-Robot 3: Cat Sensor Troubleshooting This video will show you what the DFI sensors are. What do they do, where are they, how they work and how to clean them. Also a quick tip on fixing a common ...Okay, that’s what I figured. Usually when rapid yellow appears, so does the flashing blue. You’ll need to get a DFI replacement kit and replace the DFI sensors and the pinch detect terminals. See one of my recent posts. Just went through this, and my LR is outside warranty. I have a link to their troubleshooter listed.Slow yellow blinking light. Have tried it all..!!! Litter robot 3 was working great until last week. (This model is before the app) it started to stop mid-cycle upside down, about 11:00 position, and will blink yellow (about 1 blink per second). So far we have: replaced pinch sensors, sanded down bonnet sensors, soaked entire globe to ensure no ...Why is Litter-Robot Stuck on Cycling Light? If you see a solid yellow light on the control panel, that means it is cycling (it can also mean it’s paused). Litter-Robot Cycle Light Flashing. There’re 2 types of flashing. If you see a yellow light that’s flashing slowly, it means your robot’s cycle was interrupted.Fill your Litter-Robot to the fill line with litter and then perform a hard reset on your unit. Here’s how to do a hard reset on your Litter-Robot 4: Press and hold the Reset and Power buttons for 3 seconds. The light bar will flash red then go through a sequence of red, blue and green lights then begin a cycle.So woke up this morning with litter robot 4 offline. The big light is solid blue with the little light flashing blue. How do I reconnect it? I pressed the wifi button once, goes to solid light yellow, pressed it again and goes back to blinking blue. If I press the wifi for 3 seconds, goes to flashing yellow, but nothing happens on the app. It ...Jul 22, 2020 · Cat Tips Est. read time: 5 min. Litter-Robot 3—the highest-rated automatic, self-cleaning litter box —is a machine of wonders that allows cat parents to never have to scoop cat litter again. But like any appliance, there may be times when Litter-Robot troubleshooting is required. Related: Litter-robot vs. Catlink full comparison. Another thing to note is that you should never place your Litter-Robot on an uneven surface. The Base must be on a flat surface and should not be leaning to either side. 4. Check the Lights. Your Litter-Robot’s lights are very useful in telling you what the problem might be. Make it a habit ...The following troubleshooting should resolve the blue light blinking while the waste drawer is empty. Once resolved, the unit should consistently recognize when your cat visits and cycle accordingly. To troubleshoot the blue blinking: Remove the drawer from the unit and press RESET. If the unit goes to solid blue, press the CYCLE button. The unit …If you are in warranty, go through the Whisker troubleshooter HERE for a flashing blue light or a fast flashing yellow light. And they will depending on your skill will either send a DFI pinch kit out for free or will outright replace the base unit. If you are out of warranty you can get a upgraded replacement DFI HERE for $30.Litter-Robot Connect units only – look for the WiFi symbol on the control panel. Download the Whisker app and follow the onboarding instructions. Ensure proper placement Power on Add litter Download the app 1 3 2 4 If possible, place the Litter-Robot in the same location as the old litter box (at least during transition).Opening up the Litter-Robot II To open the Litter-Robot II base, you will need a Torx T20 screwdrive and a 5/16" socket with a ratchet. First, remove the 7 torx screws around the base. Remove the Screws. With the ratchet, remove the 5/16" nut which attaches the motor to the base.Litter-Robot by Whisker November 14, 2016 · If you've been troubleshooting issues with your Litter-Robot Open Air to no avail, try this Fresh Restart to eliminate confounding conditions and identify the problem if there is one.AudioVOX July 7, 2017, 8:46am 12. @Wahoo650 You can find parts for your Litter-Robot II on our website here. kristophersullivan November 27, 2017, 12:04am 13. Open up the motor. Be Careful it’s tricky. Grab some gear oil and a few drops of white lithium grease. Quiet and smooth operation again.When I went to bed last night the robot was working fine. Completely fine. I wake up and it’s stuck on cycle (like all the way turned over like it just emptied) it’s frozen there and the cycle button is blinking. It’s recently gotten a deep clean and I took it apart and cleaned it again put it back and it still won’t work.Litter-Robot 4 continuously monitors the motor current to ensure the Globe is rotating smoothly and is not obstructed. If your unit has a red light bar with partial yellow flashing, this indicates that the Globe is most likely jammed or overloaded. You will also receive a notification on your phone if you use the Whisker App.Out little robot has a continuous yellow /amber cycling light and the control panel is totally unresponsive. Things we have tried: Cleaning the pinch sensors Checking the spring sensor Powering off and on (via plug as power button not responsive) Checking for control panel lockout Checked back clips are in Checked globe is locked at the back.Step 1: Check the Power. The first thing to do when it comes to troubleshooting a Litter Robot that is stuck mid-cycle is to check the power. Make sure the unit is plugged in and the power cord is securely connected to the unit and the outlet. If the power cord is loose, securely reconnect it. If the outlet is not functioning, try plugging the ...Mar 25, 2022 · To abort the clean cycle, press reset or empty. Press any button to put the unit on pause. On the other hand, a blinking yellow light signals a problem. How to resolve the issue depends on the flashing sequence: A slow yellow flashing light (one flash per second) Jul 22, 2020 · Litter-Robot 3 flashing red light A solid ruby light on your Litter-Robot 3 control panel means that the cat sensor was activated by to cats entered an globe while the unit was ready for getting. This unit is counting down to a clean cycle, depending on your set wait time (3, 7, instead 15 minutes). If you are in warranty, you can go HERE aMAGS How To Videos - How To Fix a Red Flashing Light on a Litter-Robot 4: Yellow Light Bar Flashing (Bonnet Removed) Litter-Robot 4: Yellow Ping-Pong Light Bar (Pinch Detect) Litter-Robot 4: Yellow Round Robin (Cycling Mode) Flashing blue light to rapid yellow. I replaced my dfi and pinch detectors 4 months ago and now when I turn on my lr3 I get a flashing blue even if the drawer is not in. When I hit reset it then goes to the rapid flashing yellow lights. I’m really getting tired of fixing this thing. A $500 litter box should be way more reliable. Omg almost ... The cycling light on your Litter Robot serve If you have a Litter-Robot III Open Air 3 and it's stopped working with yellow blinking / flashing light and/or the globe does not rotate in normal operatin...Flashing blue light to rapid yellow. I replaced my dfi and pinch detectors 4 months ago and now when I turn on my lr3 I get a flashing blue even if the drawer is not in. When I hit reset it then goes to the rapid flashing yellow lights. I’m really getting tired of fixing this thing. A $500 litter box should be way more reliable. Omg almost ... It goes from this order: reset to power. But fla

Blue and Yellow and Red (All 3 lights flashing simultaneously): This means the unit cannot find the Dump or Home position. The unit will not cycle automatically and needs repair. …Litter-Robot 4: Light Codes Guide. Litter-Robot 4 control panel features 5 buttons and an LED display for easy operation. Blue flashing. If your unit’s light bar is flashing blue, this indicates that the waste drawer is full. Empty the waste drawer, press the Reset button, then press the Cycle button. Learn more. Blue with flashing yellow WiFi.1. Empty the Drawer. On the Litter-Robot, you have a drawer that collects the cat litter. If it becomes full, the blue light will blink rapidly. But if you throw out the mess, the lights should go off. Before returning the drawer to its compartment, remember to place a new liner into the container.This video will show you what the DFI sensors are. What do they do, where are they, how they work and how to clean them. Also a quick tip on fixing a common ...Mar 25, 2022 · To abort the clean cycle, press reset or empty. Press any button to put the unit on pause. On the other hand, a blinking yellow light signals a problem. How to resolve the issue depends on the flashing sequence: A slow yellow flashing light (one flash per second)

Cycle Press the Cycle button to start a clean cycle. If already cycling, press Cycle to pause; press again to resume a cycle. A long press, while at the home position, will enter sleep mode. Reset weight scale. will enter night light setting mode. If already cycling, press Reset to pause a cycle; press again to cancel a cycle.Another reason may be that the Litter Robot is full and needs to be emptied. Lastly, the blue light may be blinking because there is a problem with the Litter Robot and it needs to be reset. The reason your Litter Robot is blinking blue is most likely because the unit is in standby mode. To wake it up, simply push the button on the front of the ...There are 2 sensors that work together to monitor if the drawer is full and needing the liner removing and replacing. The indication is a blue flashing light, and when it starts flashing, the Litter-Robot will continue to cycle automatically for approximately further cycles, allowing a little time to attend to the change of litter bag.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. The Litter-Robot 3 Connect definitely has a SafeCat system t. Possible cause: Using a flash outdoors requires you to factor in more variables to get a good shot. You ca.