Did you know?

If Litter-Robot 4 has a blue light bar with a yellow blinking light adjacent to the Connect button, this indicates that the unit is in Onboarding mode and waiting to be connected to the app. You can now proceed with the onboarding process within the Whisker App to finalize connection.Came back in an hour later and the blue light for waste drawer full is flashing again, and now it's not rotating when the cat uses it. Just sits there flashing. Pressed "reset" again. Goes back to solid blue for awhile and then within a few minutes starts flashing blue again.There could be a few reasons why the blue light is flashing on your litter robot. One reason could be that the unit is resetting itself after a power outage. Another reason could be that the unit is low on battery and needs to be recharged. There are a few reasons why the blue light might be flashing on your litter robot.Select your Litter-Robot 4. Select the Settings gear in the top right corner. Select Update Network. Follow the steps listed within the App. Once the update is complete, your Litter-Robot should be ready for use. If your unit displays a solid blue light bar, you've been successful. If your unit is not displaying a solid blue light bar, your ... Nov 10, 2021 · Hi, So I am having this issue again!!! My litter robot 3 had been flashing blue light and then yellow light (very fast) after pressing the reset button. I’ve read some troubleshooting to check for the metal pinch bars to be in contact all the time. I’ve tried to clean it and it appears to be in contact as well. The pin is not corroded as well. Please advice on what to do next. the litter ... Ours did this even after replacing the drawer sensors. After taking it completely apart, we realized that the cat sensor in the back under the drawer was too tight. It was causing it to fault every time it cycled. After some adjustment, it is now working like it should. Try to clean off the drawer sensors and adjusting the cat weight sensor.Oct 11, 2018 · Turned machine back on and it shows the yellow light on cycle but nothing happens and then the blue yellow red lights come back on. Thank you for your reply. This could be a motor problem or a malfunction from the circuit board. Turn the unit off. Remove the bonnet and globe. Litter-Robot Connect units only – look for the WiFi symbol on the control panel. Download the Whisker app and follow the onboarding instructions. Ensure proper placement Power on Add litter Download the app 1 3 2 4 If possible, place the Litter-Robot in the same location as the old litter box (at least during transition). Jan 31, 2021 · This video will show you what the DFI sensors are. What do they do, where are they, how they work and how to clean them. Also a quick tip on fixing a common ... To troubleshoot the blue blinking, let’s start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait 10 seconds then plug the unit back in 3.) Allow the unit to complete a start‐up cycle. If the light is solid blue, the code has been successfully ...Litter-Robot 4 Flashing Blue [Waste Drawer Full] Make sure waste bin is empty -> push reset button -> push cycle button Unplug from power -> check waste port in globe for clumps / obstructions -> Plug in & power on -> complete two manual cycles Litter-Robot 4 Solid Red [Cat Detected] Wait for set wait timer to complete after last cat detection (could just …My Litter Robot is blinking blue light because the power is turned on and the Litter Robot is working properly. When the Litter Robot is turned on, theBrand new Litter Robot flashing Blue - Red Sequentially. Hey everyone - we got a Litter Robot and it started flashing Blue then Red immediately after running a cycle. Chatted with customer service and they said it was an over-torque issue. They sent a new base yet I'm getting the same flashing Blue - Red lights. Litter-Robot 4 continuously monitors the motor current to ensure the GLitter-Robot Connect units only – look for the Wi Jun 12, 2018 · The following troubleshooting should resolve the blue light blinking while the waste drawer is empty. Once resolved, the unit should consistently recognize when your cat visits and cycle accordingly. To troubleshoot the blue blinking, let’s start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait ... The blue light on your litter robot is flashing to indicate t Litter-Robot 3 is equipped with infrared emitters and sensors located above the Waste Drawer that check if the drawer is full each time the Globe returns to the Home position. Once a full Waste Drawer is detected, the unit will indicate it is full with a blue flashing light.I recently purchased a litter robot 3 connected and the litter robot has been working perfectly up to this point, however, since I did my first litter empty the unit will not reset properly. I have the flashing blue light constantly. I press the reset button and I can get the blue light to remain steady but after one cycle it is back to flashing and indicating the … Jan 18, 2023 · So woke up this morni

Litter robot flashing blue light: indication and solution ... What to do when your litter robot is flashing solid yellow light? Your litter robot shows you solid yellow light when it gets paused during the cycle. The solution is very simple, just press the cycle button to continue cycling properly. If your robot is showing solid yellow light along with the …If Litter-Robot 4 has a blue light bar with a yellow blinking light adjacent to the Connect button, this indicates that the unit is in Onboarding mode and waiting to be connected to the app. You can now proceed with the onboarding process within the Whisker App to finalize connection. Hi, I just bought my Litter Robot from you 2 weeks ago. It was working fine until a few days ago, it began to stop working. Now I get a flashing blue light everytime. I’ve tried everything suggested in these forums, even left the unit unplugged for half a day and I still get a blue flashing light everytime the unit is on. The drawer is empty, the detection …Just adding that I also encountered this red/blue alternating flashing LED along with a mixed solid green/blinking red LED on litter robot 4 and what I did was remove the globe, and cleaned around the edges that lead to the litter drawer in the litter robot housing. I also wiped down the sensors at the top of the entrance into the litter robot ...Litter-Robot 3 is equipped with infrared emitters and sensors located above the Waste Drawer that check if the drawer is full each time the Globe returns to the Home position. Once a full Waste Drawer is detected, the unit will indicate it is full with a blue flashing light.

May 9, 2019 · Press and hold Cycle button for 5 seconds. Yellow light turns off, blue light remains lit. Activate the cat sensor by pressing on the globe just above the entrance in a forward and down motion. The red light should come on now. Allow the unit to complete the timing, cycle, and return to home position. At this time, the unit will have reset itself.Jul 23, 2016 · 1.) Press/Hold ‘Cycle’ button for 5 seconds. Both blue AND yellow lights are now on. 2.) Press/Hold ‘Cycle’ button for 5 seconds. Yellow light turns off, blue light remains lit. 3.) Activate the cat sensor by pressing on the globe just above the entrance in a forward and down motion. The red light should come on now. This has been happening pretty frequently. The blue ready light is almost always blinking, even though the drawer is empty or there are only a few clumps in it. I’ve tried resetting the gauge on the app as well as resetting the robot itself, hard reset with unplugging as well.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. my litter robot ready button wouldnt stop blinking blue. Possible cause: Blue and Yellow and Red (All 3 lights flashing simultaneously): This means the u.